№1066785[Quote]
You will need ammonium nitrate (NH4NO3) and nitromethane (CH3NO2). Optional are metal dusts (Al, Mg, Zn, Si) and methanol (CH3OH). For the improvised blasting cap you’ll need acetoneperoxide or HMTD - other primary explosive will work, too. Because of the easy acetoneperoxide production, it’ll be used in this project.
The ammonium nitrate has to be dried in an oven. Procedures therefor are given in US Patent No. 4,093,478 by Gerald.L. Hurst. The patent provides varios methods for the ammonium nitrate preperation, it’s basically wetting the AN and then evaporating the water resulting in reduced density and increased „oil retention“ of the ammonium nitrate.The density should be around 0,6 g/ccm to 0,8 g/ccm for the dry AN. Store it in airtight containers.
All that is needed: ammonium nitrate, nitromethane and metal dust (zinc).
Add the metal dust to the AN. Do it quick to avoid that the ammonium nitrate picks up to much moisture from the air. The exact amount of metal dust isn’t critical. A value between 3%and 10% should be OK.
You shouldn’t store the ammonium nitrate/metal dust mix, spontaneous decompostition can occur if moisture is present!
Now it’s time for the nitromethane. If you search the web for the correct ratios to use you’ll find very different opinions/data. Ragnar Benson suggests to use 70 - 80ml nitromethane for 430g ammonium nitrate, though i’m not sur eif he really uses 430g. He measures out 250ml (!) ammonium nitrate prills, assuming the density is about 1.725 g/ccm.That’s pretty stupid. The density of 1,7 g/ccm is the crystal density. Prills are never that dense. One can assume a density of 0,8 g/ccm to 1,0 g/ccm for commercial prills. I don’t understand Ragnar, he publishes books about explosives and has no access to a scale? Can’t believe it…But the ratios are ~OK.
In US Pat. No. 4,093,478 a mix of 1000g AN, 185g NM and 84g methanol is referred to as one of the most powerful ANNM explosives.If you use only nitromethane, take something around 250g (220ml) for 1000g ammonium nitrate.When adding the nitromethane it would be the best to pour it onto the ammonium nitrate in the blasting container without stirring etc. It’ll sensitize better if not disturbed. But i observed that not all AN may be wetted with the nitromethane, so a little bit of stirring is OK. Seal airtight as soon as possible.
The ANNM explosive is now ready to use. All you need to detonate it, is a blasting cap. You’ll be shown how to manufacture one now.
№1066786[Quote]
First you need acetoneperoxide or HMTD. I assume you knowhow to produce some, but i included my method here.The pic shows the yield of 40ml acetone & 40ml 30% H2O2.
Acetoneperoxide:
Equal amounts of acetone and 30% hydrogen peroxide are mixed in a glassbeaker and cooled to below 10 °C (ice bath, fridge etc.). For 100mlacetone/ hydrogen peroxide mix ca. 30ml 37% HCl is used. Add the acid in little portions over a period of ca. 20 minutes with occasional stirring. If you don’t use an ice bath, put the beaker in the fridge to cool between the acid additions. After all the acid is added put the glass back in the fridge.Now it depends on you how patient you are. You could filter the whole shit after 30-60 minutes getting acceptable yields. Waiting for 6-8 hours will reward you with a much grater yield.(You can wait even longer, but with 6-8 hours you've got most of the AP and the crystals are still like flour. Waiting for longer will result in larger AP crystals that are more senstitive!)To filter add 150ml distilled water to the AP (should be a thick, white slurry) to dilute the acid and make the shit pourable for filtering. One can use a normal paper- coffee filter without any problems. Put the slurry on the filter and wash with distilled water until pH is nearly neutral. Now spread the AP on flat surface to dry.
HMTD:
14g powdered hexamine fuel tablets (hexamethylentetramine) are stirred in 45g (39.8ml) 30% hydrogen peroxide. 21g of powdered citric acid is added to this mixture and the beaker is put in the refrigerator (+ 3 °C). After 24 – 48 hours the HMTD cake is diluted with the same amount distilled water, washed neutral in paper- coffee filter with distilled water. The last wash is made with denatured ethanol to speed up the drying process.
Once you have dry AP (acetoneperoxide) or HMTD, you need a suitable container. Here a strong walled glass tube is used, 100mm x 10mm (outer diameter) 8mm inner diameter. It’s carefully filled a few mm high with AP. Then the AP is pressed down with a plastic rod. This is repeated until the tube contains ca. 1g AP.
The tube is filled with ca. 1g acetone peroxide. Be careful not to use a too close fitting rod to press the AP – the friction could cause an accidental detonation. After filling it, remove all remaining AP from the walls of the tube.
A little bit black powder is put on top of the AP. To hold the fuse in place, a piece of paper is rolled to a tube and inserted in the glass tube.
This is the finished detonator. Securing the fuse with a bit of adhesive tape might be a good idea. Insert full length into explosive, to ensure detonation.
№1066787[Quote]
This is not my guide. I am forwarding it here for educational purposes. I have zero plans for creating this compound myself, and I do not encourage others to do so.